Sump Pump – GJ MacRae Foundation Repair https://wetbasements.com Sat, 22 Jun 2024 15:24:34 +0000 en-CA hourly 1 https://wordpress.org/?v=6.4.5 https://wetbasements.com/wp-content/uploads/2024/02/review-photo-png-1-150x150.png Sump Pump – GJ MacRae Foundation Repair https://wetbasements.com 32 32 Sump Basin and 1/3hp Sump Pump Install (Brampton) https://wetbasements.com/project/sump-basin-and-1-3hp-sump-pump-install-brampton/ Sat, 22 Jun 2024 15:24:34 +0000 https://wetbasements.com/?post_type=project&p=14643 Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

]]> Sump Pump and Basin Installation in Port Credit (Mississauga) https://wetbasements.com/project/sump-pump-and-basin-installation-in-port-credit-mississauga/ Fri, 14 Jun 2024 03:52:27 +0000 https://wetbasements.com/?post_type=project&p=14306 Remove all loose obstructions in way of repair areas.

Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Reinstall concrete floor. Remove and dump all debris.

]]> Outside Basement Waterproofing with Window Well and Sump Install (Mississauga) https://wetbasements.com/project/outside-basement-waterproofing-with-window-well-and-sump-install-mississauga/ Fri, 14 Jun 2024 03:42:08 +0000 https://wetbasements.com/?post_type=project&p=14290 Remove all debris and obstructions in way of repair areas. Lay down tarps and dig down to footing by hand in specified repair areas.

Repair all cracks and masonry voids in foundation wall below grade. Prime wall and apply hydroshield rubberized membrane to repair area. Add a layer of mastic mesh, another layer of hydroshield rubberized membrane, a layer of 12m plastic and fasten drainage board to grade with termination straps and concrete anchors.

Replace weeping tile system within repair areas and cover with 6″ of 3/4″ clear gravel. Install fresh vertical drains in window wells and fasten new window wells to foundation walls. Backfill and power tamp dirt. Cover new drains in window wells with 3/4″ clear gravel and level.

On the interior, break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel. Install a 1/3hp oil cooled sump pump and connect pump exhaust line.

Reinstall concrete floor. Backfill exterior. Remove and dump all debris.

]]> Carbon Fiber Foundation Reinforcement with Sump Pump Install (Oakville) https://wetbasements.com/project/carbon-fiber-foundation-reinforcement-with-sump-pump-install-oakville/ Fri, 14 Jun 2024 02:45:37 +0000 https://wetbasements.com/?post_type=project&p=14245 Break open concrete floor and expose footing in proposed carbon fiber reinforcement installation areas. Remove all debris from concrete foundation wall and clean thoroughly. Expose sill plate/joist work and prepare for hardware mounting. Drill 1″ hole in concrete footing and clean debris from hole.

Generously cover concrete wall with resin and install carbon fiber strips directly to foundation wall. Run carbon fiber overtop of exposed footing and curl base of strip into footing. Fill 1″ hole with resin and coat entire front side of carbon fiber generously with resin. Fasten top of carbon fiber into sillplate/joistwork and tighten hardware.

Break open concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filtercloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line into. Reinstall concrete floor. Parge wall in sump box enclosure.

Reinstall concrete floor. Remove and dump all debris. All labour and materials included.

]]> Outside Basement Waterproofing with Sump Battery Backup Install (Collingwood) https://wetbasements.com/project/outside-basement-waterproofing-with-sump-battery-backup-install-collingwood/ Fri, 14 Jun 2024 02:28:18 +0000 https://wetbasements.com/?post_type=project&p=14225 Remove all debris and obstructions in way of repair areas and lay down tarps and dig down to footing by hand in specified repair areas.

Repair all cracks and masonry voids in foundation wall below grade. Prime wall and apply rubberized membrane to repair area. Add a layer of mastic mesh, another layer of rubberized membrane, a layer of 12m plastic and fasten drainage board to grade with termination straps and concrete anchors.

Repair weeping tile system and cover with 6″ of 3/4″ clear gravel. Install fresh vertical drains in window wells and fasten new window wells to foundation walls.

On interior of basement, break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel. Install a 1/3hp oil cooled sump pump and connect pump exhaust line and reinstall concrete floor.

Cover new drains in window wells with 3/4″ clear gravel and level.

On exterior, backfill and power tamp dirt. Remove and dump all debris.

]]> Inside Basement Waterproofing with Sump Pump Install (Oakville) https://wetbasements.com/project/inside-basement-waterproofing-with-sump-pump-install-oakville/ Fri, 14 Jun 2024 02:14:43 +0000 https://wetbasements.com/?post_type=project&p=14215 Break concrete 18″ back from foundation walls around the complete perimeter of repair area. Dig down to footings and remove debris.

Drill 1/2″ holes in cavities of blockwork and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filter cloth.

Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel. Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to new sump basin and reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

]]> Outside Basement Waterproofing with Sump Pump Installation (Burlington) https://wetbasements.com/project/outside-basement-waterproofing-with-sump-pump-installation-burlington/ Fri, 14 Jun 2024 02:08:38 +0000 https://wetbasements.com/?post_type=project&p=14210 Saw cut asphalt and remove. Lay down tarps and dig down to footing by hand in specified repair areas.

Repair all cracks and masonry voids in foundation wall below grade. Once cured, apply AB-720-38 rubberized membrane to repair area. Add a layer of mastic mesh, another layer of AB-720-38 rubberized membrane, a layer of 12m plastic and fasten drainage board to grade with termination straps and concrete anchors.

Replace weeping tile system within repair areas and cover with 6″ of 3/4″ clear gravel. On inside of basement, break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Reinstall concrete floor. On exterior, backfill and power tamp dirt. Remove and dump all debris.

All labour and materials are included.

]]> Outside Basement Waterproofing with Window Well Repair (Brampton) https://wetbasements.com/project/outside-basement-waterproofing-with-window-well-repair-brampton/ Fri, 14 Jun 2024 01:54:08 +0000 https://wetbasements.com/?post_type=project&p=14202 Remove all debris and obstructions in way of repair areas. Lay down tarps and dig down to footing by hand in specified repair areas.

Repair all cracks and masonry voids in foundation wall below grade. Prime wall and apply hydroshield rubberized membrane to repair area. Add a layer of mastic mesh, another layer of hydroshield rubberized membrane, a layer of 12m plastic and fasten drainage board to grade with termination straps and concrete anchors.

Replace weeping tile system within repair areas and cover with 6″ of 3/4″ clear gravel. Install fresh vertical drains in window wells and fasten new window wells to foundation walls. Backfill and power tamp dirt. Cover new drains in window wells with 3/4″ clear gravel and level.

Backfill and power tamp dirt.

]]> Outside Basement Waterproofing in Riverside (Toronto) https://wetbasements.com/project/outside-basement-waterproofing-in-riverside-toronto/ Wed, 12 Jun 2024 17:09:13 +0000 https://wetbasements.com/?post_type=project&p=14039 Remove all debris and obstructions in way of repair areas. Lay down tarps and dig down to footing by hand in specified repair areas. Repair all cracks and masonry voids in foundation wall below grade and parge with type-s masonry. Prime wall and apply rubberized membrane to repair area. Add a layer of mastic mesh, another layer of rubberized membrane, a layer of 12m plastic and fasten drainage board to grade with termination straps and concrete anchors. Remove and replace existing weeping tile system with a new 4″ perforated weeping tile with filter sock and cover with gravel. Backfill and power tamp dirt.

On interior, break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to sump basin. Reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

]]> Inside Basement Waterproofing with Sump Pump (Hamilton) https://wetbasements.com/project/inside-basement-waterproofing-with-sump-pump-hamilton/ Wed, 12 Jun 2024 17:04:39 +0000 https://wetbasements.com/?post_type=project&p=14036 On interior, remove all loose obstructions in way of repair areas. Break concrete 18″ back from foundation walls around the complete perimeter of repair area. Dig down to footings and remove debris.

Drill 1/2″ holes in cavities of blockwork and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filter cloth. Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to sump basin. Reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

]]>