Drill 1/2″ holes in cavities of blockwork and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filter cloth.

Connect fresh weeping tile system into existing drain works. Cover weeping tile with 3/4″ gravel and reinstall concrete floor.

Remove and dump all debris. All labour and materials included.

Generously cover concrete wall with resin and install carbon fiber strips directly to foundation wall. Run carbon fiber overtop of exposed footing and curl base of strip into footing. Fill 1″ hole with resin and coat entire front side of carbon fiber generously with resin. Fasten top of carbon fiber into sillplate/joistwork and tighten hardware.

Break open concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filtercloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line into. Reinstall concrete floor. Parge wall in sump box enclosure.

Reinstall concrete floor. Remove and dump all debris. All labour and materials included.

Generously cover concrete wall with resin and install carbon fiber strips directly to foundation wall. Run carbon fiber overtop of exposed footing and curl base of strip into proposed underpinning. Fasten top of carbon fiber into sillplate/joistwork and tighten hardware.

Excavate underpin by hand and clean underside of footing with wire brush. Apply masonry adhesive to underside of footing. Once underpin is carved and prepared, build and install timber forms to accommodate a positive concrete adhesion to the underside of existing footings (non-grout, overflow method) allowing for a void-less encapsulation of existing structure to fresh underpin.

Fill forms with 25 MPa concrete until full and install needle vibrator and fill exterior blockwork with slurry grout.

Once cured, remove timber forms and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filter cloth.

Connect fresh weeping tile system into existing drain works. Cover weeping tile with 3/4″ gravel and reinstall concrete floor.

Remove and dump all debris. All labour and materials included.

Drill 1/2″ holes in cavities of blockwork and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filter cloth.

Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel. Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to new sump basin and reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

Drill 1/2″ holes in cavities of blockwork and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filter cloth. Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filter cloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to sump basin. Reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

Install fresh vertical iron posts and plates where applicable and pour specified concrete footings for posts. Fasten new vertical posts to existing wood beam with approved hardware. Once post footings are cured, remove shoring and rest structure onto new post/footings installations.

Begin underpinning excavation of debris through side access window directly to disposal bin. Once full excavation of underpinned sectionals has concluded, remove timber forms and install a complete 4” interior weeping tile system with filter cloth. Chip all loose debris from foundation walls and repair all masonry voids in existing foundation walls with S-type masonry. Once cured, fasten drainage board around complete interior perimeter from grade to base of fresh underpins.

Install sump box next to proposed services area (customer to determine preferred sump box location). Connect fresh 4“ weeping tile system into proposed sump box and install a 1/3hp cast iron oil cooled sump pump with check valve into sump basin. Install 8” of 3/4” clear gravel throughout entire basement floor. Once level and complete, proposed plumbing rough-in modifications are to take place (not included in below price).

Once full structural and plumbing inspections are completed, install a 4” concrete floor by hand and float level. Remove and dump all debris. All labour and materials included.

Remove existing sump basin. Dig larger pit and line with landscape fabric. Reinstall sump basin.

Install 4″ of base gravel and pour a new 4″ concrete floor using minimum 25 MPa concrete and float level by hand.

Remove and dump all debris. All labour and materials are included.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to sump basin. Reinstall concrete floor. Remove and dump all debris. All labour and materials are included.

Repair all cracks and masonry voids in foundation wall below grade. Prime wall and apply hydroshield rubberized membrane to repair area. Add a layer of mastic mesh, another layer of rubberized membrane, a layer of 12m plastic and fasten drainage board to grade with termination straps and concrete anchors. Backfill and power tamp dirt. On interior, remove all loose obstructions in way of repair areas. Break concrete 18″ back from foundation walls around the complete perimeter of repair area. Dig down to footings and remove debris.

Drill 1/2″ holes in cavities of blockwork (if applicable) and fasten drainage board to foundation wall using concrete anchors. Install a fresh 4″ perforated weeping tile system with filtercloth. Break open existing concrete floor and excavate sump basin at a dimension of approximately 2.5ft x 2.5ft x 3ft. Line perimeter of basin with filtercloth and drill 1/2” holes around complete perimeter of basin. Install basin and surround with 3/4“ clear gravel.

Install a 1/3hp oil cooled sump pump and connect pump exhaust line. Connect fresh weeping tile system to sump basin. Reinstall concrete floor. Remove and dump all debris. All labour and materials are included.